Every detection visit includes a full equipment pad inspection, pressure testing of the return and suction lines, dye testing of the shell and fittings, and a written finding with photos and a repair price. Repair is quoted separately so you can decide what to fix and when.
We check the pump, filter, heater, valves, and all visible plumbing at the pad. Loose fittings, cracked valve bodies, and heater connections are common leak points. This takes 15 to 20 minutes and often finds the problem before we pressurize anything.
We isolate each return and suction line and pressurize it with gauges. A pressure drop tells us which line is leaking. This is the most reliable way to find underground pool leaks without digging up the whole yard.
We use leak detection dye at the skimmer throat, light niche, main drain, and any visible shell cracks. Dye gets pulled into the leak, showing us exactly where water is escaping. It is simple, fast, and accurate.
A FLIR thermal camera shows temperature differences caused by escaping water. We scan the deck, shell, and equipment area to find leaks that are not visible to the eye. This is especially useful for underground pool leak detection Brea CA jobs.
You get photos of the leak, a description of the cause, and a repair price before we start any work. No surprises, no pressure. If you want a second opinion, you have everything you need to get one.
Pool Leak Detection in Brea is the process of finding where your pool is losing water, using pressure testing, dye testing, and electronic listening gear to isolate the leak before we dig or drain anything. We start at the equipment pad, check the pump, filter, heater, and valves, then pressure-test the return and suction lines. If the plumbing holds, we move to the shell, skimmer, light niche, and main drain. Most leaks show up at pipe joints, fittings, or cracked skimmer throats, and we confirm the exact spot with a pipe inspection camera before recommending a fix.
Brea pools sit on clay-heavy soil and older copper or PVC plumbing that expands and contracts hard through hot inland summers. A pool losing water leak detection Brea CA call usually comes after a homeowner notices the waterline dropping faster than evaporation explains, or a soggy patch near the pad. We also handle underground pool leak detection Brea CA work when the leak is under decking or turf. If you have been searching pool leak detection near me Brea, we can usually be on site the same day.
Every job follows the same five steps, whether it is a spa losing an inch overnight or a commercial pool in Central Brea. You get a clear finding and a price before we touch a pipe.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Acoustic listening devices
Pick up the sound of water escaping a pressurized line. We use them to narrow down which return or suction line is leaking before we dig or cut into decking.
FLIR thermal imaging cameras
Show temperature differences caused by escaping water. We scan the deck, shell, and equipment area to find leaks that are not visible to the eye.
Pressure testing gauges
Isolate and pressurize each pool line. A pressure drop tells us which line is leaking. This is the most reliable way to find underground pool leaks without digging.
RIDGID pipe inspection cameras
See inside pool return and suction lines. We use them to confirm the exact leak location and check for root intrusion or pipe collapse before recommending a repair.
Sewerin tracer gas detectors
Trace underground leaks by injecting a safe tracer gas into the line and following it to the surface. Useful when acoustic listening is not enough.
Moisture meters
Measure water content in soil and concrete. We use them to confirm whether a wet spot is from the pool, irrigation, or a slab leak.
Leak detection dye
Confirm leaks at the skimmer throat, light niche, main drain, and shell cracks. Dye gets pulled into the leak, showing us exactly where water is escaping.
Pressure testing
We isolate each pool line and pressurize it with gauges. If the pressure drops, that line is leaking. This method finds underground leaks without digging and tells us whether the problem is in the plumbing or the shell.
Dye testing
We apply leak detection dye at the skimmer throat, light niche, main drain, and any visible shell cracks. Dye gets pulled into the leak, showing us the exact spot. It is simple, fast, and accurate for shell leaks.
Thermal imaging
We scan the deck, shell, and equipment area with a FLIR camera. Escaping water changes the surface temperature, so the camera shows us where the leak is even under concrete or turf. Non-invasive and fast.
Acoustic listening
We use acoustic listening devices to hear water escaping a pressurized line. This narrows down which line is leaking before we dig. It works best on copper and PVC pipes under pressure.
Tracer gas detection
We inject a safe tracer gas into the suspect line and follow it to the surface with a Sewerin detector. This is the most accurate way to pinpoint an underground leak when acoustic listening is not enough.
01
What we do: We come out same day, pressure-test the return and suction lines, and dye-test the shell. Most Brea pools losing this much water have a skimmer throat crack or a failed light niche gasket. We find it and quote the repair.
→ You stop refilling, the water bill drops back to normal, and the pool holds its level within 24 hours of repair.
02
What we do: We inspect the pad, check the pump basket and valves, then pressure-test the suction line. If the leak is underground, we use acoustic listening devices to pinpoint it and repair the pipe with new PVC and fittings.
→ The pump holds prime, the wet spot dries up, and you avoid a pump motor replacement.
03
What we do: We test both. We pressure-test the pool lines, isolate the irrigation system, and use thermal imaging to see where the water is coming from. You get a clear answer and a repair quote.
→ You fix the right problem the first time and avoid tearing up the deck twice.
04
What we do: We run a full detection with pressure testing, dye testing, and thermal imaging. You get a written finding with photos and a repair price you can use in negotiations or to plan the fix.
→ You know exactly what you are buying and what the repair will cost before you close.
Brea pools sit on clay-heavy soil that expands when wet and shrinks when dry, which puts stress on underground plumbing. Most homes here were built between the 1960s and the 2000s, so you see a mix of copper pipes in older neighborhoods like Birch Hills and PVC or PEX in newer builds like La Floresta. Summer temperatures hit 95 to 105 degrees, and pool water evaporates fast, which is why a real leak is easy to miss until the water bill spikes. We run pool leak detection Brea CA near me calls year-round, but fall and winter are when underground line leaks show up because the soil shifts. If you are searching for 24/7 pool leak repair in Brea California, we can be on site the same day. We also handle pool losing water leak detection Brea CA jobs where the leak is under decking or turf.
Birch Hills
Older pools with copper plumbing and original skimmers. Skimmer throat cracks and failed light niche gaskets are common here because the plaster is 40 to 50 years old.
La Floresta
Newer builds with PVC and PEX plumbing. Leaks here are usually at fittings and valve connections rather than in the pipe itself. Pressure testing finds them fast.
Downtown Brea
A mix of older and renovated pools. Many have been replumbed once already, so we check for both new PVC leaks and old copper lines that were left in place.
Olinda Ranch
Larger lots with longer pipe runs from the equipment pad to the pool. Longer runs mean more joints, and more joints mean more chances for a leak. Acoustic listening works well here.
Country Hills
Sloped lots where pool plumbing runs downhill from the pad. Gravity keeps pressure on the joints, so leaks here tend to show up as wet spots at the bottom of the slope.
Clay-heavy soil that expands and contracts
This movement stresses underground pool lines and causes joints to fail. Most Brea pool leaks we find are at pipe joints, not in the middle of a pipe run.
Summer temperatures of 95 to 105 degrees
Evaporation can hit two inches a week, which masks a real leak. We measure water loss over 24 hours with the pump off to separate evaporation from a leak.
Older pools with copper plumbing
Copper pipes in Brea pools from the 1960s and 1970s develop pinhole leaks and joint failures. We pressure-test each line and use a pipe inspection camera to confirm the condition.
Winter rain and soil saturation
Saturated soil raises the water table and can mask or mimic a pool leak. We test in dry conditions when possible and use moisture meters to separate rain water from a real leak.
Most Brea pool leaks fall into five categories. We find and fix all of them, from a slow skimmer leak to a full underground line failure.
Problem
At one inch per day, you are losing about 600 gallons a week and spending $40 to $80 extra on water and chemicals every month. The leak also dilutes chlorine, so algae blooms faster.
Our Fix
We pressure-test the lines and dye-test the shell to find the source. Most Brea pools losing this much water have a cracked skimmer throat or a failed light niche gasket. We repair both underwater with epoxy putty and sealant, usually in under two hours.
Problem
A wet spot at the pad usually means a leaking fitting or valve. Left alone, it can wash out the pad base, rust the pump housing, and short the heater. It also wastes water 24/7.
Our Fix
We inspect the pad, tighten or replace fittings, and pressure-test the lines feeding the pad. If the leak is underground, we use acoustic listening devices to pinpoint it and repair the pipe with new PVC and fittings.
Problem
Water escaping under a deck softens soil and causes concrete to settle or crack. A small leak can turn into a $5,000 deck repair within a season if it is not found.
Our Fix
We use thermal imaging cameras and moisture meters to map where the water is going. Once we find the leak, we repair the line and pressure-test it. You can then repair the deck knowing the source is fixed.
Problem
A hidden pool leak can run for months before you notice. By then you have paid hundreds in extra water and possibly damaged the deck or foundation.
Our Fix
We run a full detection including pressure testing, dye testing, and thermal imaging. If the pool holds pressure, we check the autofill line and irrigation system. We find the leak, quote the repair, and fix it.
Problem
A pump that keeps losing prime is pulling air through a leak on the suction side. Running dry overheats the pump and can burn out the motor, which is a $400 to $800 replacement.
Our Fix
We pressure-test the suction line and check the pump basket, valves, and fittings. Most prime loss in Brea pools comes from a cracked valve or a leaking union. We repair it and confirm the pump holds prime before we leave.
A leaking pool wastes water, wrecks chemistry, and can undermine decking or a nearby foundation. Finding the leak fast keeps the repair small and the bill lower.
Stop water loss fast
A pool leaking one inch per day wastes roughly 600 gallons a week. We pinpoint the source with acoustic listening devices and pressure testing gauges so you stop refilling and stop overpaying on water. Most Brea homeowners see the waterline hold steady within 24 hours of repair.
Protect deck and foundation
Water escaping under a pool deck can soften soil and crack concrete within a season. Our thermal imaging cameras and moisture meters map where the water is actually going, so we fix the leak before it reaches your patio, slab, or a nearby foundation wall.
Save on chemicals
A leaking pool constantly dilutes chlorine and stabilizer, so you keep buying chemicals that wash away. Once we seal the leak, your sanitizer holds its level and your monthly chemical spend drops. Brea customers routinely cut pool chemical costs by a third after repair.
Same-day answers
We run 24/7 emergency response for pools losing more than two inches a day. Call (657) 681-3703 and a tech arrives with electronic leak detection equipment and tracer gas detectors ready. You get a written finding and a repair price before we start any work.
Google ★★★★★4.9
Found a leak two other companies missed. They used a thermal camera and pressure gauges, found a cracked return line under the deck, and fixed it the same day. Price was fair and they cleaned up after themselves. Highly recommend for pool leak detection in Brea.
Yelp ★★★★★4.8
Our pool was losing an inch a day and we were ready to replaster. These guys dye-tested the skimmer, found a crack, and fixed it underwater in under two hours. Saved us thousands. Honest and professional.
BBB ★★★★★5.0
Commercial pool was losing 2,000 gallons a week. They came out after hours, found the leak with a tracer gas detector, and had it repaired by morning. No downtime for our tenants. Will use again.
Google ★★★★★4.9
Called at 7 a.m. with a pool losing two inches a day. They were on site by 10 a.m., pressure-tested the lines, and found a failed joint under the deck. Repaired it the same day. Fair price and no upsell.
Brea Leak Detection Pros has been finding and fixing pool leaks since 2011. Our techs hold a California State Plumbing License and C-36 Plumbing Contractor License, and we follow Uniform Plumbing Code and California Building Standards Code on every repair. We have worked on everything from 1970s plaster pools in Birch Hills to new builds in La Floresta with PEX and PVC plumbing. Our gear includes RIDGID pipe inspection cameras, Sewerin tracer gas detectors, and FLIR thermal cameras. We know how Brea soil, sun, and pool chemistry affect plumbing, and we use that to find leaks faster.
Real experiences from customers who chose our Pool Leak Detection services.
“My pool was losing an inch a day and I was refilling it every other morning. Brea Leak Detection Pros came out same day, pressure-tested the lines, and found a cracked skimmer throat. They fixed it underwater with epoxy and the water level has held for three months. Cost was $380 for the detection and $450 for the repair.”
Mark R.
Homeowner, Downtown Brea
“We had a soggy spot near the equipment pad and two other companies told us we needed a full replumb. These guys used a thermal camera and found one leaking return line joint under the deck. They cut out a two-foot section, replaced it with PVC, and pressure-tested it. Saved us thousands.”
Sandra L.
Homeowner, La Floresta
“I manage a commercial pool that was losing 2,000 gallons a week. Brea Leak Detection Pros came out after hours, used acoustic listening devices and a tracer gas detector, and found a leak in the main drain line. They had it repaired and pressure-tested by the next morning. No downtime for tenants.”
Tom W.
Property Manager, Central Brea
Real answers to the questions we hear most often from local homeowners and property managers.
If your pool equipment pad sits near the house and you see a warm spot on the slab, the leak may be under the foundation. We use thermal imaging and pressure testing to tell a pool line leak from a slab leak before either gets worse.
View Slab Leak DetectionPool plumbing and house plumbing often share a trench. When we pressure-test a pool return line and it holds, we check the house side with acoustic listening devices and moisture meters so you are not chasing the wrong pipe.
View Plumbing Leak DetectionPool heaters run on gas, and a leaking gas line near the equipment pad is a safety issue. We use Sewerin tracer gas detectors to check heater connections and supply lines while we are on site for pool leak detection.
View Gas Leak DetectionAcoustic listening devices pick up the sound of water escaping a pressurized line. We use them on every Brea pool job to narrow down which return or suction line is leaking before we dig or cut into decking.
View Acoustic Leak DetectionFLIR thermal cameras show temperature differences caused by escaping water. On Brea pool decks, that means we can see a leak under concrete or turf without tearing anything up first. It is fast and non-invasive.
View Thermal Imaging Leak DetectionElectronic leak detection equipment picks up moisture and pressure changes that eyes and hands miss. We run it on pool shells, equipment pads, and underground lines to confirm a leak before we recommend a repair.
View Electronic Leak DetectionCall (657) 681-3703 any time, day or night. A live dispatcher answers, asks a few questions about what you are seeing or smelling, and gets a tech headed your way. Most Brea calls get a same-day window, and emergency calls roll 24/7. You can also email [email protected] and we will respond within one business hour during regular hours.
Phone
(657) 681-3703Address
200 Fig Ave, Brea, CA 92821, USA
Hours
Monday–Sunday: 7 Days a Week
Open 24 Hours
Same-Day Service
24/7 Emergency Available
